The pool is available in many families. If the pool is of poor quality, it will seep. This will cause a lot of trouble for people's lives and make people feel particularly uneasy. What method can be used to repair the leaking water in the pool, and what glue to use to repair the leaking water in the pool must be mastered. We must deal with it as soon as possible to minimize the damage.

the cause of water leakage in the pool can not be found

For many families, leaking water from the pool is a common problem. If you want to repair the pool, you must find the cause of the leak. Then why ca n’t you find the cause of the leak? Let ’s take a look.

1. Defects in construction. Generally, the bottom of the pool body and the concrete of the pool wall are poured twice. If the construction joints are not handled properly, it will bring hidden dangers to waterproofing. After the middle buried water stop is installed, it is easy to run away when pouring concrete. During construction, the water stop may be pulled or cracked in the middle, which may cause construction joint leakage.

Due to the large volume of concrete, the vibration is not in place during pouring, which causes pitting at a very small number of points, and when pouring concrete, due to untimely supply of concrete, a small number of cold joints have occurred.

2. There is no water stop ring or the size of the water stop ring does not meet the requirements of the specification, and the water stop ring is not fully welded, which results in the formation of a gap around the bolt hole of the concrete structure and water leakage.


what methods can be used to repair the leaking water in the pool

1. The surface repair method is mainly applicable to slender seams. It is common to lay thin film materials along the same crack surface, such as epoxy resin or resin-impregnated glass cloth. For clean water pools, non-toxic and pollution-free environmental protection materials must be used. Select the appropriate material according to the reference requirements.

2. Filling method When the crack is wide, v-shaped or u-shaped grooves can be created along the cracked concrete surface. Filling with resin mortar material, or using materials such as impervious mortar or asphalt, the surface is strengthened by the above method. Similarly, after the treatment is completed, it is necessary to wait 7 days before the subsequent construction, so as to avoid the failure of the filling material.

3. Injection method When the crack width is small and deep, a repair method of injecting repair material into the concrete can be used. First, an injection pipe is set at the crack, and then it is sealed by surface treatment.


What glue is used for pool leakage

In terms of filling the leaking water in the pool, everyone will choose the simplest way to fill the leak. The simplest way is to need some filling products to fill the leak. Then the manufacturer of China Stainless Steel Sink will give Let me introduce what glue to use for the leak in the pool.

1. For cracks with a large number of cracks, small crack widths, and most impenetrable cracks, waterproof cement mortar can be applied on the water front. The five-layer waterproofing method with better effect is especially suitable for conditions with low head. . The cyanide coating can also be used for waterproofing, that is, the cyanide slurry is coated on the surface of the leaking water to form a watertight cover layer. This is a good treatment method with convenient construction.

2. For wide and seepage cracks, plugging measures should be taken. The principle is to change the large leak to a small leak, the line leak to a point leak, the chip leak to an empty leak, so that the leakage is concentrated at one or a few points, and finally block.

The commonly used plugging material is setting accelerator, that is, adding an appropriate amount of setting accelerator to the cement slurry or cement mortar (the currently used setting accelerator is mainly water glass, and it is prepared by adding a certain proportion of copper sulfate and potassium dichromate. ). For plugging without strength requirements, it can also be treated with coagulating liquid materials such as cyan condensate and acrylic condensate.

3. Acrylic high-elasticity anti-cracking waterproof coating is good. You can also try JS polymer waterproof coating. It has excellent waterproof performance, and also has the advantages of high elasticity of organic materials and good durability of inorganic materials. It is good. Environmental protection, impervious and waterproof material. You can do it yourself. You can use waterproof black gold steel super-permeable waterproof guard to make waterproof.

information about China Stainless Steel Sink : https://www.afastainlesskb.com/product/stainless-steel-sink/