China Bed Elevator Supplier Introduces The Elevator Installation Strategy
222-6-15
Home elevators are elevators that are installed in private residences and are intended for use by a single-family member only. It can be installed in a building not used by a single-family as a means of entry for a single family to their residence, but not accessible and usable by the public or other occupants of the building. Below,China Bed Elevator Supplier introduce home elevator installation considerations:

The first is that before the installation of the home elevator, the problems and dangers that may occur during the installation of the home elevator need to be listed as much as possible to reduce the danger during the elevator installation. The source of the problem in the installation may come from the environment, tools, and equipment, or from the operation.

In addition, it may also come from customers and users, their own colleagues, and may also come from unrelated people. Check whether the mental state of yourself and your colleagues is good, whether personal protective equipment and safety protection equipment is carried and in good condition, and whether the tools are sufficient and in good condition.

Followed by some problems in the installation of home elevators, we are installing to prevent safety protection equipment, wear personal protection equipment, control and clean up the dangerous sources that affect work; operate according to the correct construction steps, do not violate regulations, do not take risks, do not take chances, and do not opportunistically. Colleagues should communicate and cooperate with each other, monitor and supervise each other, immediately point out and ask for immediate correction if any violations are found, and keep the workplace clean and orderly.

After the home elevator is installed, the site must be cleared after the installation is completed, and the safety of the elevator must be checked, and only when the protective measures are in place can you leave.

Through the above introduction,Escalator Supplier hopes that you can simply refer to the content of this article in future use.
www.fujihsed.com

China Escalator Suppliers Introduces The Classification Knowledge Of Escalators
2022-5-12
China Escalator Suppliers introduces the classification knowledge of 5 kinds of escalators

(1) Classification according to the driving mode: there are two types of chain type (end drive) and rack and pinion type (intermediate drive).

(2) According to the conditions of use: there is ordinary type (running time less than 140h per week) and public transportation type (running time more than 140h per week).

(3) According to the lifting height: there are three types of small lifting heights up to 8m, medium lifting heights up to 25m, and large lifting heights up to 65m.

(4) According to the running speed: there are two kinds of constant speed and adjustable speed.

(5) According to the running track of the steps: there are 4 types of linear type (traditional type), spiral type, runway type, and rotary spiral type.

Through the above introduction, Automobile Elevator Suppliers hopes that you can simply refer to the content of this article for future use.
https://www.fujihsed.com/

Passenger Elevator Manufacturers Introduces The Use Of Bed Elevators
2022-4-21

The competition of elevator technology has not only stayed on the running speed and safety performance, but people's requirements for elevator comfort are getting higher and higher. For the use environment of the Bed Elevator , how to improve its comfort to reduce the pain of patients is particularly important. Therefore,Passenger Elevator Manufacturers Introduces the main measures taken are as follows:

1. The car is equipped with a fan with large air volume and low noise to solve the problem of a sultry car.

2. Ventilation holes should be provided in the upper and lower parts of the car without holes. The effective area of the ventilation holes located in the upper and lower parts of the car should not be less than 1% of the effective area of the car. Therefore, rivet nuts are used in the design to connect the upper and lower ends of the surrounding arms to the car top and bottom to realize the ventilation and ventilation area. Regulation.

3. In order to reduce the vibration and noise of the car, a hoisting machine with small torsional vibration and low noise is used; three-stage vibration damping is designed: the traction machine vibration damping pad, the rope head combination, and the car vibration damping pad.

Through the above introduction, Luxury Home Elevator Factory hopes that you can simply refer to the content of this article in future use.

https://www.fujihsed.com/